top of page
vmep pre-order.png

This Power Distribution Module is ideal for race cars and motorcycles which have minimal onboard electrical circuits but still require rugged and reliable protection and control.

 

Simple connections and no configuration procedures makes this system very easy to use and quick to install.

 

The 4 x 10 amp outputs can be used to control power to various devices such as ECUs, instrumentation, lighting, starter solenoid, radiator fan, etc.

 

Channels will automatically shut down if a short circuit or over-current is detected – LED Status indication on the PDM and Cartek Switch Panels makes fault finding simple.

 

The Cartek Power Distribution Module Kit is a direct replacement for 4 x 10amp Fuses, 4 Relays and 4 Switches. This unit therefore reduces all the wiring in between the Fuses, Relays and Switches as well as simplifying the installation.

 

When mounting the PDM, electrical contact must be made between the vehicle’s chassis/earth and the metal case of the PDM at its mounting points. 12v Power Input is supplied to the PDM via the M6 electrical stud. Power Output connections are made using 6.3mm spade terminals.

 

Each channel is turned ON by connecting the corresponding channel signal wire to chassis/earth. Connection can be made using dashboard switches, oil pressure switches, thermo-switches, etc. When a Cartek Switch Panel (pushbutton switches with integrated LED) is used then the LED will display the channel status:

 

   No LED   = Channel OFF

   LED on    = Channel ON

   Flashing  = ERROR

 

When short-circuit or over current is detected, the PDM will shut down that channel and the corresponding LED will begin to flash. To reset the error, switch the channel OFF then ON again.

 

SIZE: L = 90mm W=42mm
WEIGHT: 80g
POSITIVE POWER TERMINAL: M6 BRASS STUD
CHANNEL OUTPUT CONNECTIONS: 6.3mm MALE SPADE TERMINALS
OPERATIONAL VOLTAGE: 7V-18V
POWER SWITCHING CURRENT: 10A MAX EACH CHANNEL
CURRENT CONSUMPTION: 0.02A (NO LOAD)
OPERATING TEMPERATURE: -10°C – +85°C

 

CK-PS-04 PDM SWITCH PANEL

4x Black latching switches with LED status indication.
Blank panel for over-writing.

 

CK-PS-05 PDM SWITCH PANEL

3x Black latching switches with LED status indication plus Green momentary switch.
Blank panel for over-writing.

 

CK-PS-13 PDM SWITCH PANEL

3x Black latching switches with LED status indication plus Green momentary switch.
Panel marked with IGN, FUEL, ACC, START.

 

CK-PS-06 PDM SWITCH PANEL

4x Coloured latching switches with LED status indication.
Blank panel for over-writing.

 

CK-PS-07 PDM SWITCH PANEL

3x Colour latching switches with LED status indication plus Green momentary switch.
Blank panel for over-writing.

 

CK-PS-14 PDM SWITCH PANEL

3x Coloured latching switches with LED status indication plus Green momentary switch.
Panel marked with IGN, FUEL, ACC, START.

 

CK-PP-28 PDM SWITCH PANEL

4x Black latching switches with LED status indication
plus Fire Extinguisher button
plus Battery Isolator GT ON/OFF button.
Blank panel for over-writing.

 

CK-PP-05 PDM SWITCH PANEL

3X BLACK LATCHING SWITCHES WITH LED STATUS INDICATION

plus Green momentary switch plus Fire Extinguisher button
plus Battery Isolator GT ON/OFF button.
Blank panel for over-writing.

 

CK-PP-06 PDM SWITCH PANEL

3x Black latching switches with LED status indication
plus Green momentary switch plus Fire Extinguisher button
plus Battery Isolator GT ON/OFF button.
Panel marked with FUEL, DASH, START, RAIN.

 

 

Cartek Power Distribution Modules & Switch Panels

129,50£Prix
    bottom of page