This product is a full redesign of Cartek's successful but bespoke, Power Control Panels, with the main aim of allowing the user to customise and configure it themselves.
The CARTEK Power Distribution Panel is an all-in-one solid state solution to power distribution in your race car. Designed to replace all the Fuses, Relays and Switches – this unit greatly simplifies the wiring, saving weight and maximising reliability.
The CARTEK Power Distribution Panel is a Power Control Unit and Switch panel in one, The main advantage of using a Power Distribution Panel is that it directly replaces Fuses, Relays, Switches and all the wiring in between.
Features:
● 8/16 User Configurable Channels (no Laptop required)
● Selectable current settings of 5, 10 or 15 Amps. Combine two channels together for 20, 25 or 30 Amps
● Selectable Functions such as:
– Momentary action (Starter Motor, Washer Pump etc)
– Latching (with memory)
– Latching (without memory)
– Latching with Time Delay (Heated Screen)
– Flashing (Indicators etc)
– Toggling (Headlights High Beam/Low Beam)
– 0v Momentary action (use as ordinary switch for ECU Map etc)
● Over Current and Short Circuit Protection – no Fuses or Relays needed.
● Multi coloured Label Sheet included for full customisation.
● 2 Back light settings as standard.
● 8/16 Momentary Switch Inputs – allowing any channel to be operated by an additional switch or the CARTEK Wireless Control System.
● 8/16 ECU Inputs – allows the ECU to turn on channels such as Fuel Pumps.
● 4 Dedicated function inputs – Flash Input for Lights, Wash Input for Wipers, Wiper Park position etc.
Unlike most PDM’s on the market this Power Distribution Panel does not need a laptop to program the configuration. Preset options for functionality and current settings can be chosen by going through a simple process via the switch panel. This saves the user time and any potential labour costs in setting it up.
The CARTEK Power Distribution Panel is one of the most cost-effective solutions on the market due to the switch panel being designed as part of the package, whereas most other PDM’s require expensive CAN-Bus Switch Panels to be purchased and programmed separately.
Two Sticker sets come with every Power Distribution Panel:
1) Multi-coloured Label Set
2) Black and white Label Set
Both Label sets allow back light illumination.
CARTEK offer a choice of connection packages, each sold separately.
PDP-16
CK-PDP-CC: Two connectors and 39 crimped wires (30-50cm wire length)
CK-PDP-LF: Two connectors and 50 loose crimps (wiring & crimp tool required)
PDP-08
CK-PDP-CA: One connector and 20 crimped wires (30-50cm wire length)
CK-PDP-LD: One connector and 25 loose crimps (wiring & crimp tool required)
The Power Distribution Panel has two dedicated pins that can take in the Kill Signal from a CARTEK Battery Isolator XR. This will then shut down the Power Distribution Panel which will stop the engine from running if the ECU is powered by the Power Distribution Panel.
The Power Distribution Panel also has 16 switch inputs and 4 dedicated inputs, meaning you can use our Wireless Control System to activate and control channels.
CARTEK also produce a smaller 4 Channel Power Distribution Module that can be used if you need to power more channels.
The 4 x 10 amp outputs can be used to control power to various devices such as ECUs, instrumentation, lighting, starter solenoid, radiator fan, etc.
Channels will automatically shut down if a short circuit or over-current is detected – LED Status indication on the PDM makes fault finding simple.
Part Numbers: | CK-PDP-08 | CK-PDP-16 |
Size: | W=140 mm, L=145 mm | W=140mm, L=195mm, |
Weight: | 450g | 600g |
Rear connectors: | AMP 1-776231-1, M6 Stud for Power Input | AMP 1-776231-1, AMP 1-776231-5, M6 Stud for Power Input |
Operating Voltage: | 6-12v | 6-12v |
Total Output Current: | 80 A (Continuous) | 160 A (Continuous) |
Current Settings: | 0A, 5A, 10A, 15A, 20A, 25A, 30A | 0A, 5A, 10A, 15A, 20A, 25A, 30A |
Power Outputs | 8 | 16 |
ECU Inputs | 8 | 16 |
Switch Inputs/Outputs | 8 | 16 |
Battery Isolator XR Signal Inputs | 1 | 2 |
Operating Temperature: | -10 -+85 | -10 -+85 |
Wiper Control | Dedicated Wiper module with park position input. | Dedicated Wiper module with park position input. |
Back Light | Low and High power settings | Low and High power settings |
Environmental Protection: | Front and Rear Gaskets, protection from Dirt. | Front and Rear Gaskets, protection from Dirt. |